Search Results

This paper presents the development of a transmission closed loop pressure control system. The objective of this system is to improve transmission pressure control accuracy by employing closed-loop technology. The control system design includes both feed forward and feedback control. The feed forward control algorithm continuously learns solenoid P-I characteristics. The closed loop feedback control has a conventional PID control with multi-level gain selections for each control channel, as well as different operating points. To further improve the system performance, Robust Optimization is carried out to determine the optimal set of control parameters and controller hardware design factors. The optimized design is verified via an L18 experiment on spin dynamometer. The design is also tested on vehicle.

The perceived interior noise has been one of the major driving factors in the design of automotive interior assemblies. Buzz, Squeak and Rattle (BSR) issues are one of the major contributors toward the perceived quality in a vehicle. Traditionally BSR issues have been identified and rectified through extensive hardware testing. In order to reduce the product development cycle and minimize the number of costly hardware builds, however, one must rely on engineering analysis and simulation upfront in the design cycle. In this paper, an analytical and experimental study to identify potential BSR locations in a cockpit assembly is presented. The analytical investigation utilizes a novel and practical methodology, implemented in the software tool Nhance.BSR, for identification and ranking of potential BSR issues. The emphasis here is to evaluate the software for the BSR predictions and the identification of modeling issues, rather than to evaluate the cockpit design itself for BSR issues.

Automotive rollover is a complex mechanical phenomenon. In order to understand the mechanism of rollover and develop any potential countermeasures for occupant protection, efficient and repeatable laboratory tests are necessary. However, these tests are not well understood and are still an active area of research interest. It is not always easy or intuitive to estimate the necessary initial and boundary conditions for such tests to assure repeatability. This task can be even more challenging when rollover is a second or third event (e.g. frontal impact followed by a rollover). In addition, often vehicle and occupant kinematics need to be estimated a-priori, first for the safe operation of the crew and equipment safety, and second for capturing and recording the event. It is important to achieve the required vehicle kinematics in an efficient manner and thus reduce repetitive tests. Mathematical modeling of the phenomenon can greatly assist in understanding such kinematics.

Adaptive Cruise Control (ACC) technology is presently emerging in the automotive market as a convenience function intended to reduce driver workload. It allows the host vehicle to maintain a set speed and distance from preceding vehicles by a forward object detection sensor. The forward object detection sensor is the focal point of the ACC control system, which determines and regulates vehicle acceleration and deceleration through a powertrain torque control system and an automatic brake control system. This paper presents a design of an automatic braking system that utilizes a microprocessor-controlled brake hydraulic modulator. The alternatively qualified automatic braking means is reviewed first. The product level requirements of the performance, robustness, and durability for an automatic brake system are addressed. A brief overview of the presented system architecture is described.

This paper proposes the concept of Generalized Diagnostic Component (GDC) and presents a modular fault diagnostic strategy for safety critical automotive systems. The diagnostic strategy makes full use of hierarchical techniques, integrates the generalized diagnostic design into all-purpose vehicle diagnoses based on reconfiguration of the GDCs, and inherits the model-based diagnostic algorithms developed for Steering/Braking-By-Wire systems. The GDC-based approach simplifies the design and integration of diagnostics in complex dynamical control systems, and has been successfully implemented in an eight degrees of freedom NAVDyn (Non-Linear Analysis of Vehicle Dynamics) simulation model using Matlab Simulink. The simulation results are provided in this paper to testify that the diagnostic strategy and implementation are feasible, efficient and dependable.

Implementation of engine turnoff at idle is desirable to gain improvements in vehicle fuel economy. There are a number of alternatives for implementation of the restarting function, including the existing cranking motor, a 12V or 36V belt-starter, a crankshaft integrated-starter-generator (ISG), and other, more complex hybrid powertrain architectures. Of these options, the 12V belt-alternator-starter (BAS) offers strong potential for fast, quiet starting at a lower system cost and complexity than higher-power 36V alternatives. Two challenges are 1) the need to accelerate a large engine to idle speed quickly, and 2) dynamic torque control during the start for smoothness. In the absence of a higher power electrical machine to accomplish these tasks, combustion-assisted starting has been studied as a potential method of aiding a 12V accessory drive belt-alternator-starter in the starting process on larger engines.

A new single-brick Ba + alkali metals NOx-Trap catalyst has been developed to replace a two-brick NOx-Trap system containing a downstream three-way catalyst. Major development efforts include: 1) platinum group metals selection for higher HC oxidation with potassium-containing washcoat, 2) alumina and ceria selection, and Rh architecture design for more efficient NOx reduction and 3) NiO to suppress H2S odor. Mitsubishi Motors' 1.8L GDI™ with this Delphi new NOx-Trap catalyst with H2S control achieves J-LEV standard with less cost and lower backpressure compared to the previous model. It is further discovered that incorporation of NiO into the NOx-Trap washcoat is effective for H2S control during sulfur purge but has a negative impact on thermal durability and sulfur resistance. Further study to improve this trade-off has been made and preliminary results of an advanced washcoat design are presented in this paper. Details will be reported in a future publication.

Since its invention in early 1990s, the side curtain airbag has become an important part of the occupant restraint system for side impact and rollover protection. Computer Aided Engineering (CAE) is often used to help side curtain airbag design. Because of the unique characteristics of side curtain airbag systems, the simulation of side curtain airbag systems faces different challenges in comparison to the simulation of driver and passenger airbag systems. The typical side curtain airbag CAE analysis includes, but is not limited to, cushion volume evaluation, cushion coverage review, cushion shrinkage and tension force review, deployment timing review and seam shape and location review. The commonly used uniform pressure airbag models serve the purpose in most cases.

This paper reviews the state of the art on analytical design of cockpit modules in two most crucial performance categories: safety and comfort. On safety, applications of finite element analysis (FEA) for achieving robust designs that meet FMVSS 201, 208 and 214 requirements and score top frontal and side NCAP star-ratings are presented. On comfort, focus is placed on Noise, Vibration and Harshness (NVH) performance. Cutting-edge analytical tools for Buzz, Squeak and Rattle (BSR) avoidance and passenger compartment noise reduction are demonstrated. Most of the analytical results shown in this paper are based on the development work of a real-life application program. Correlations between the analytical results and physical test results are included. Examples of Computational Fluid Dynamics (CFD) analysis for climate control are also included. At the end, the road map toward 100 percent virtual prototyping and validation is presented.

Computer modeling and simulation have become one of the primary methods for development and design of automobile occupant protection systems (OPS). To ensure the accuracy and reliability of a math-based OPS design, the correlation quality assessment of mathematical models is essential for program success. In a typical industrial approach, correlation quality is assessed by comparing chart characteristics and scored based on an engineer's modeling experience and judgment. However, due to the complexity of the OPS models and their responses, a systematic approach is needed for accuracy and consistency. In this paper, a correlation grading methodology for the OPS models is presented. The grading system evaluates a wide spectrum of a computer model's performances, including kinematics, dynamic responses, and dummy injury measurements. Statistical analysis is utilized to compare the time histories of the tested and simulated dynamic responses.

The interaction between the deploying airbag and the Out-Of-Position (OOP) occupants remains a challenge in occupant protection system simulations. The integration of Computational Fluid Dynamics (CFD) analysis into Finite Element (FE) airbag model is a helpful and important tool to address this challenge. Three major commercial crash simulation software packages widely used in the automotive safety industry, LS-DYNA, MADYMO and PAM-CRASH are in the process of implementing different approaches for airbag CFD simulation. In this study, an attempt was made to evaluate and compare the CFD integrated airbag models in these software packages. Specially designed tests were conducted to study and capture the pressure distribution inside a flat airbag and the test results were used for the evaluation. Strengths and limitations of each software package are discussed in this paper.

Regulatory and market pressures continue to challenge the automotive industry to develop technologies focused on reducing exhaust emissions and improving fuel economy. This paper introduces a practical model, which evaluates the economic value of various technologies based on their ability to reduce fuel consumption, improve emissions or provide consumer benefits such as improved performance. By evaluating the individual elements of economic value as viewed by the OEM manufacturer, while keeping the end consumer in mind, technology selection decisions can be made. These elements include annual fuel usage, vehicle performance, mass reduction and emissions, among others. The following technologies are discussed and evaluated: gasoline direct injection, variable valvetrain technologies, common-rail diesel and hybrid vehicles.

A seat belt usability study was conducted to investigate factors associated with seat belt comfort and convenience related to shoulder belt contact pressure, shoulder belt fit, and seat belt upper anchorage location. Two major objectives were addressed in this study: (1) Determine the shift in the contact pressure while changing the seat back angle and seat belt attachment points / B-pillar location by utilizing a body pressure measurement system; (2) Identify how seat belt contact pressure and fit affect users' subjective feeling of comfort. Results from the statistical analysis shows that the seat belt contact pressure increases when the D-ring moves away from the driver in the fore-aft direction (X-axis) whereas height adjustment of the D-ring (Z-axis) is not statistically significant in terms of pressure distribution.

The concept of condenser, fan, and radiator power train cooling module (CFRM) was further evaluated via three-dimensional computational fluid dynamics (CFD) studies in the present paper for vehicle at idle conditions. The analysis shows that the CFRM configuration was more prone to the problem of front-end air re-circulation as compared with the conventional condenser, radiator, and fan power train cooling module (CRFM). The enhanced front-end air re-circulation leads to a higher air temperature passing through the condenser. The higher air temperature, left unimproved, could render the vehicle air conditioning (AC) unit ineffective. The analysis also shows that the front-end air re-circulation can be reduced with an added sealing between the CFRM package and the front of the vehicle, making the CFRM package acceptable at the vehicle idle conditions.

An integrated optimization system has been developed to combine optimization algorithms with Finite Element Analysis for airbag design. A number of industry standard software packages are employed to work in coherence to complete the optimization procedure automatically with minimal user intervention. The system can be easily tailored to fit multiple performance requirements and various design constraints for different airbag systems. Compared with the commonly used Design of Experiment (DOE) method, time and computer resources requirements are greatly curtailed. The integrated optimization system was successfully used in single-chamber and dual-chamber airbag optimizations. The results proved the effectiveness of the system and demonstrated its capability in product design.

Electro-hydraulic actuation has been used widely in automatic transmission designs. With greater demand for premium shift quality of automatic transmissions, higher pressure control accuracy of the transmission electro-hydraulic control system has become one of the main factors for meeting this growing demand. This demand has been the driving force for the development of closed loop pressure controls technology. This paper presents the further research done based upon a previously developed closed loop system. The focus for this research is on the system requirements, such as solenoid driver selection and system latency handling. Both spin-stand and test vehicle setups are discussed in detail. Test results for various configurations are given.

The information provided by the in-cylinder pressure signal is of great importance for modern engine management systems. The obtained information is implemented to improve the control and diagnostics of the combustion process in order to meet the stringent emission regulations and to improve vehicle reliability and drivability. The work presented in this paper covers the experimental study and proposes a comprehensive and practical solution for the estimation of the in-cylinder pressure from the crankshaft speed fluctuation. Also, the paper emphasizes the feasibility and practicality aspects of the estimation techniques, for the real-time online application. In this study an engine dynamics model based estimation method is proposed. A discrete-time transformed form of a rigid-body crankshaft dynamics model is constructed based on the kinetic energy theorem, as the basis expression for total torque estimation.

2-step variable valve actuation using early-intake valve closing is a strategy for high fuel economy on spark-ignited gasoline engines. Two discrete valve-lift profiles are used with continuously variable cam phasing. 2-step VVA systems are attractive because of their low cost/benefit, relative simplicity, and ease-of-packaging on new and existing engines. A 2-step VVA system was designed and integrated on a 4-valve-per-cylinder 4.2L line-6 engine. Simulation tools were used to develop valve lift profiles for high fuel economy and low NOx emissions. The intake lift profiles had equal lift for both valves and were designed for high airflow & residual capacity in order to minimize valvetrain switching during the EPA drive cycle. It was determined that an enhanced combustion system was needed to maximize fuel economy benefit with the selected valve lift profiles. A flow-efficient chamber mask was developed to increase in-cylinder tumble motion and combustion rates.

This paper reviews the current strategies for physical prototyping of Magnesium instrument panel (I/P) structures. Bottlenecks in the traditional physical prototype based product development process are discussed. As demand for fast-to-market and cost-reduction mounts, virtual prototyping becomes increasingly important in meeting the timing and performance goals. A virtual prototyping methodology is presented in this paper to enable high performance Magnesium I/P structures in Safety, NVH, and initial part quality aspects. Examples of Finite Element Analysis (FEA) results and correlations are included.

The intensity of a combustion flame ionization current signal (ionsense) can be used to monitor and control combustion in individual cylinders during a cold engine start. The rapid detection of poor or absence of combustion can be used to determine fuel delivery corrections that may prevent engine stalls. With the ionsense cold start control active, no start failures were recorded even when the initially (prior to ionsense correction) commanded fueling had failed to produce a combustible mixture. This new dimension in fuel control allows for leaner cold start calibrations that would still be robust against the possible use of low volatility gasoline. Consequently, when California Phase 2 fuel is used, cold start hydrocarbon emissions could be lowered without the risk of an engine stall if the appropriate fuel is replaced with a less volatile one.